CyberMaxLink8000+ 10W/20W/200W VHF/UHF STL 音頻鏈路

描述

Need to send your audio from studio to the remote transmitter? Now with 1-200W of power and covering also UHF band! CyberMaxLink8000+ VHF/UHF Studio to Transmitter audio link is a MPX Stereo wideband FM audio transport system providing high quality broadcast audio wireless bridge. These systems offer great value and work either in MPX or two-channel stereo mode and offer excellent overall performance.

主要特點:
– Synthesized from 45-850MHz (specify 10MHz segment at the time of ordering)
– The transmitted and received frequency can be set by LCD display on front panel (UP/DOWN keys)
– Suitable for MPX systems (stereo encoder in studio) or for 2-channel systems (2 audio channels, left+right, with 19KHz notch filter to prevent beat frequency)
– Built-in speaker for easy monitoring at the receiving side
– Low THD distortion: the THD value with stereo or mono demodulated and deemphasized signals is negligible
– Flat frequency response
– Excellent signal to noise ratio either in mono or in stereo
– High sensitivity and RF immunity
– High adjacent channel rejection
– LCD Display: shows frequency and a number of other parameters (temperature, voltage etc)

Technical specifications for transmitter:
– Synthesized from 45-500MHz (specify 10MHz segment at the time of ordering)
– PLL step: 100KHz
– Modulation: FM, ±75 KHz peak deviation
– Frequency stability: <±200 Hz
– Output power: 10, 20W, 50W or 200W, adjustable from 0 to max via LCD display
– 輸出阻抗：50Ω不平衡，全輸出時駐波比小於2:1
– RF output connector: BNC female (rear panel)
– RF Spurious: >-75 dBc @ +- 1MHz min. away from carrier
– RF Harmonics: > -50-60 dBc Standard
– 監控 LED：開機、SWR/TEMP/PLL 錯誤
– Audio input connectors: RCA (cinch) and XLR (DSP version)
– 音頻電平：1Vpp
– 音頻輸入阻抗：10Kohms
– 預加重：平坦，50 或 75usec，可調
– Audio channel frequency response: 20 to 15 KHz ± 0.15 dB
– MPX input frequency response: 10 to 100 KHz ± 0.15 dB
– AUX input frequency response: 10 to 100 KHz ± 0.15 dB
– 諧波失真 (THD)：> 0.1%（0.05% 典型值）
– Channel separation: 40 dB min., 20Hz to 15kHz
– AUX / MPX input level: -10 to +13 dBm @±75 KHz deviation
– AUX channel input impedance: 10K
– MPX and AUX input connector: BNC-female
– Power supply: 110-240V 50/60Hz
– Operating temperature range: -15 to 45C
– Dimensions : 483 x 88 x 150 mm , rack std. 19”2U
– Weight: 2Kg

Technical specifications for receiver:
– Available for frequency: 45MHz-850MHz (specify 10MHz segment at the time of ordering)
– Built-in speaker for easy monitoring
– Sensitivity: ~1uV 10dB SINAD (varies with frequency band, falls rapidly above 600-900MHz, can be corrected with preamplifier)
– Frequency response MPX: 20 Hz to 60 KHz ±0.1 dB
– Stereo separation: 20 Hz to 15 KHz >40 dB
– 19KHz notch attenation: > 60 dB
– S/N Ratio : >65 dB @-40 dBm , 75 KHz dev. and 1 KHz mod.
– THD : 20 Hz to 53 KHz <0.3%
– Selectivity: ±160 KHz at -3 dB IF BW, ±500 KHz at -62 dB IF BW
– Image rejection: >65 dB
– Stereo audio output impedance: 50 ohm balanced
– Stereo audio output connector: RCA/CINCH female
– MPX output impedance: 75R
– MPX output connector: BNC female and XLR balanced
– Headphones output: >2×0.2 W stereo at 32 ohms
– Headphones output connector: 3.5mm stereo phone jack
– RF input impedance: 50ohm
– RF input connector: BNC Type – female
– AC power: 85~264VAC; 120~370VDC, full range universal input, can also work from 12-15V DC
– Power consumption: approx 20W from AC
– Operating temperature range: -15 to 50C
– Dimensions : 483 x 44 x 130 mm , rack std. 19”1U
– Weight: 2Kg

What’s included:
CyberMaxLink6000+ 10W/20W TX+RX includes receiver and 10W/20W transmitter (1H rack) with mains power supply for both RX and TX. Transmitter is equipped with DSP STEREO ENCODER. You can use this link in either 2 separate channel mode or as a MPX link (in this case set encoder to mono and use MPX IN BNC at the back). RDS encoder is not included by default, you can add it if you wish.
Antenna is not included, you have to select it as it is listed separately below. More antenna types available 這裡。

CyberMaxLink6000+ 50W/200W TX+RX includes receiver and 50W/200W transmitter with built-in universal mains power supply for both RX and TX. You can use this link in either 2 separate channel mode or as a MPX link (in this case set encoder to mono and use MPX IN BNC at the back). RDS encoder is not included by default, you can add it if you wish.
Antenna is not included, you have to select it as it is listed separately below. More antenna types available 這裡。

IMPORTANT!
– At the time of ordering please specify 10MHz frequency band, for example 210-220MHz! Units work best at the frequency they are set at in the factory!

To look for an alternative antenna check: 這裡。
要尋找合適的同軸電纜，請檢查： 這裡。
我們所有的手冊和軟件都可用 這裡.