คู่มือ Idiot เกี่ยวกับพาวเวอร์ซัพพลาย
If you’re planning to power your transmitter from batteries than skip this section! You might want to read it to get an idea of what it takes to power transmitter off the mains voltage.
ทรานสมิตเตอร์ขนาดเล็กที่ผลิตเองหรือใช้พลังงานต่ำส่วนใหญ่ต้องการ 12-15 โวลต์ที่ดี, 2A (ขั้นต่ำ) ถึง 10A (ตัวส่งสัญญาณที่แรงกว่า 50W หรือ 100W) stabilized mains power supply. Note stabilized was printed in bold type, meaning output voltage is regulated and stabilized to specific voltage with minimum noise or fluctuation. The noise can usually be heard as a hum (50/60Hz). If switching power supply is used noise can appear at the switching frequency and produce weird results when mixing with other signals in the transmitter.
Wall-wart types are sometimes not of stabilized type. Worst can output even 20V when in load-free mode and only go down to rated 12V under load. This is not what you want to use as it may damage your transmitter and will definitely present as a strong 50/60Hz hum on your signal from the lack of proper stabilization. Short circuit protection is useful but not mandatory. A fuse serves well instead of protection and you should definitely use one. They cost 5 cents and a final RF transistor can cost you more than 100 US$/Euro.
แรงดันไฟขาออกที่ปรับได้ช่วยให้คุณมีคุณสมบัติเพิ่มเติม คุณจะสามารถเปลี่ยนกำลังขับของเครื่องส่งสัญญาณได้โดยการเปลี่ยนแรงดันไฟฟ้าของแหล่งจ่ายไฟของคุณ ไม่เลว. บางครั้งคุณสามารถบีบพลังงานออกจากเครื่องส่งสัญญาณได้มากขึ้น หากคุณเพิ่มแรงดันไฟฟ้าเกินพิกัดสำหรับเครื่องส่งสัญญาณของคุณเพียงเล็กน้อย แต่ระวังด้วย เพราะสิ่งนี้มีแนวโน้มที่จะทำลายทรานซิสเตอร์เอาต์พุตของคุณ ทำให้ตัวเก็บประจุด้วยไฟฟ้าบางส่วนระเบิดหรือทำให้เกิดความร้อนมากเกินไป เครื่องกระตุ้น MAXPRO อาจใช้เวลานานถึง 15.5V สูงสุดก่อนเกิดความเสียหาย
Importance of proper power supply is often underestimated. Poor power supply can cause several serious problems; add hum to your signal, cause interference to your neighbors (typical for AM systems where RF leaks into power lines), low current rating, unstable operation under RF field etc. Complicated laboratory power supply units with lots of poorly shielded electronics are often susceptible to RF fields meaning they can uncontrollably raise their output voltage or short-circuit protection can trip when the current is not even reaching 10% of the limit. A good power supply for transmitters should be RF shielded.
ในปัจจุบันมีหน่วยที่ยอมรับได้ในราคาที่ต่อรอง ร้านค้าออนไลน์เช่น Mouser หรือ Digikey มีตลอดจนร้านวิทยุแฮมและเทศกาลแฮม เราขายหลายรุ่นด้วยตัวเราเอง ที่นี่. มีรุ่นแรงดันต่ำ 15V ให้เลือก ที่นี่. เครื่องส่งสัญญาณที่แรงกว่ามักจะทำงานจาก 48V หรือ 65V ของเรา แหล่งจ่ายไฟหลักที่แข็งแกร่งที่สุด สามารถส่งพลังงานได้ถึงประมาณ 2000W เครื่องส่งสัญญาณ FM หากคุณต้องการสร้างอุปกรณ์ด้วยตัวเอง ให้เตรียมหัวแร้งและตรวจสอบโครงการด้านล่างนี้ ปฏิบัติตามกฎความปลอดภัยเสมอเมื่อจัดการกับแรงดันไฟหลัก ความผิดพลาดอาจถึงแก่ชีวิตได้!
แหล่งจ่ายไฟ 1A ที่ปรับได้
This is a simple variable output power supply. Now, left of this circuit would be standard line voltage transformer (110-220/18V) and a standard rectifier block with smoothing caps (10000uF or more). The heatsink of the 317 regulator must be isolated from the ground (aluminum heatsink).
3A 13.8V แหล่งจ่ายไฟแรงดันคงที่;
นี่เป็นวงจรสเตรทไปข้างหน้า คุณอาจต้องเลี่ยงผ่าน C5 ด้วยตัวเก็บประจุที่ใหญ่กว่า (10-100uF) Diode D ชดเชยการสูญเสีย BE 0.7V ของทรานซิสเตอร์ 2N3055 หากคุณต้องการแรงดันไฟฟ้าที่สูงขึ้น ให้ใช้ 7815 แทน 7812 และต่อพิน 3 กับกราวด์โดยตรง สิ่งนี้จะให้เอาต์พุต 14-14.3V แก่คุณ ฉันสร้างอุปกรณ์จ่ายไฟแบบนี้สำหรับสถานี CB/แฮม และทำงานได้ดีมาก แน่นอนคุณต้องเพิ่มหม้อแปลงไฟฟ้าหลักและบริดจ์วงจรเรียงกระแส + ฝาปิดที่ราบเรียบเหมือนด้านบน แคปควรมีขนาดใหญ่ที่สุด (2000uF หรือมากกว่า)
แหล่งจ่ายไฟกระแสสูง 28V สำหรับเครื่องขยายสัญญาณ RF 40-200W;
การออกแบบนี้มาจากคู่มือ ARRL 2005 เราขอแนะนำหนังสือเล่มนี้ให้กับทุกคน เนื่องจากหนังสือเล่มนี้ครอบคลุมทุกแง่มุมในการออกแบบ RF รวมถึงเสาอากาศ เครื่องส่งสัญญาณ electronics พื้นฐาน ตัวกรอง เครื่องขยายเสียง และอื่นๆ พาวเวอร์ซัพพลายนี้สะดวกมากสำหรับแอมพลิฟายเออร์ RF 40-200W ซึ่งมักจะทำงานจาก 24V ตรวจสอบคู่มือ ARRL สำหรับเค้าโครง PCB และรายละเอียดเพิ่มเติม เรายังมีลิงค์ไปยังหนังสือเล่มนี้ในของเรา การอ่านที่แนะนำ ส่วน.
พูดคุยบทความนี้ในของเรา ฟอรั่ม!