Akcija!

MAXPRO2015+ mikro FM vzbujevalnik

 3,99 -  144,99

Na zalogi
Šifra: 15W pri 12V Kategorija:
 89,99

Na zalogi

 28,99

Na zalogi

 4,99

Na zalogi

 9,90

Na zalogi

 5,99

Na zalogi

 59,99

Na zalogi

 39,99

Na zalogi

 74,99

Na zalogi

 44,99

Na zalogi

 144,99

Na zalogi

 69,99

Na zalogi

 4,99 -  7,99

Na zalogi

 19,99

Na zalogi

Prikazane cene so brez DDV (plača se samo v EU)

Opis

DIP stikalo ali LCD zaslon, polna konstantna moč v celotnem pasu FM brez uglaševanja in 15 W čiste moči!

The new MAX PRO 2015+ mikro FM exciter is a simplified version of our MAX PRO 8015+. Although this version lacks some of the features of the MAXPRO8015+ it still represents a big improvement over the old MAX PRO 2015+. It covers entire FM band from 87.5 to 108MHz without tuning and offers 15W of clean RF power. 76MHz band is also available on request.

MAXPRO2015+ micro was created as a smaller version of high-performance exciter board and is based on the simplified version of MAXPRO8015+. The result is a rugged and solid FM exciter with completely flat power output across the entire FM band at up to 15W, designed to run silently and cool 24/7. Why wait? Your dream FM exciter is a reality right now!

Vzbujevalnik ima enoletno omejeno garancijo na dele in delo proti napakam v materialu in izdelavi, razen RF tranzistorja.

Priročnik najdete tukaj.

What is new about version: mikro?
– Extra external sensors (voltage, temperature) ensure some of DIGIAMP functionality
– Fast tuning
– Faster power-up
– Improved PLL
– Much improved audio response. Especially the bass response and high frequency roll-off
– Much smaller board
– Frequency adjustment trimmer
– Extra power limit steps (500mW)

Ali lahko navedete preprost primer uporabe?
MAXPRO2015+ mikro is very easy to setup:
1. Ploščo namestite v kovinsko ohišje
2. Set power limit jumper to desired setting with jumpers (you can select 0.5W, 1W, 2W, 3W, 4W, 5W, 6W, 7W, 8W, 9W, 10W….or 15W)
3. Če LCD zaslona ne uporabljate, nastavite frekvenco s stikalom DIP (sicer lahko uporabite LCD zaslon)
4. Connect antenna, audio input and supply voltage
5. Napajanje lahko spremenite z LCD zaslonom ali s skakalci.
6. You can add stereo encoder, the best matching unit is SE8000 DSP+

Kako deluje z ojačevalniki za pogon?
MAXPRO2015+ je zelo enostaven za nastavitev ojačevalnika palet:
- Mostiček za omejitev moči nastavite na želeno moč pogona s pomočjo mostičkov (lahko izberete 1W, 2W, 3W, 4W, 5W, 6W, 7W, 8W, 9W, 10W…. Ali 15W)
– Connect the SWR and power reading voltage to P and S input pins. Optionally connect also U to amplifier voltage and T to 10K NTC resistor (to ground) to measure temperature
– Set the power meter voltage sensitivity as you wish and the exciter will never drive your amp beyond preset value.
- Omejitev moči ojačevalnika lahko nastavite tudi z LCD -prikazovalnikom (na primer 500 W ali 1000 W).

 

Katere parametre lahko spremenim z daljinskim upravljalnikom?
Its best that you look at the screen capture below. The program may change over time as we make enhancements, we will be adding more features soon! Feel free to ask for any features you may want. The board is compatible with control software for MAXPRO8015 (CyberMaxFM+ SE3.

PC control software

Tehnične specifikacije:
– RF Output Power: 0 to 15 Watts, power adjustment range can also be limited to 0-0.5W, 0-1W, 0-2W, 0-3W, 0-4W … 0-15W, 0-full, this is done with a jumper (exact options vary depending on model).
– Output connector: MCX female connector, pigtails are available to easily connect N female
- Izhodna impedanca: 50 ohmov
-Frekvenčni razpon: 87,5-108MHz
- Koraki PLL: 100KHz
- Frekvenčna stabilnost: +/- 20Hz
– Spurious/Harmonic rejection: Harmonics: >55dB, Spurious: >-60dB
-Napajanje 13-15V/2.5A ali avtomobilska baterija
- Priključek za napajanje: spajkanje na plošči
- Krmiljenje frekvence PLL s ključavnico
- Ultra stabilen, ultra čist izhod
- draga preskusna oprema ni potrebna
-Zvočna zmogljivost: Popačenje manj kot 0,1%, 20Hz-75KHz
- Robustnost RF izhoda: zaščita SWR
- Zaščita polarnosti, zaščita pred temp
– Pre-emphasis: none (set on stereo encoder)
- Avdio vhodna impedanca: 1Kohm, neuravnotežena
- Raven avdio vhoda: 0 dB
– razmerje S/N: >90 dB
– PC Board Size: 75x108mm
– Audio connectors: 2-pin header or RCA (optional)
- RF monitor: spajkalne blazinice

Kaj je avdio vhodna plošča MPX (RCA+XLR+ 192KHz USB) + 20cm ploščati kabel?
– Rather than the BNC MPX input as before all MPX input models now have:
– RCA and balanced XLR inputs
– USB audio input supporting 192KHz sample rate!
– The usual BNC as before (signal is now passed through extra limiter low pass filter)
– Board can be configured to pass full MPX or limit at 15KHz (for mono operation) with a jumper.
– Extra limiter stage for MPX input
– Extra MPX low pass filter
– MPX level trimmer accesible through hole next to XLR connector (you can adjust MPX level/ deviation without opening up the transmitter

The result with this board is completely noise-free audio in any possible configuration. Important: This board is only recommended when you do not use SE8000DSP+ stereo encoder! When you have stereo encoder you do not need it!

Kaj je predvrtana sprednja plošča LCD?
- To je pravokoten kos aluminija s predhodno izvrtanimi luknjami za LCD zaslon, gumbe in LED diode. V kotu ima tudi 4 luknje, tako da ga lahko enostavno pritrdite na ohišje. Tako je oddajnik veliko lažje namestiti v lepo ohišje (odpravlja težko delo z LCD -zaslonom). To je seveda neobvezna postavka.

Kaj je IO plošča in zakaj jo potrebujem?
IO board is required, if you want to control MAXPRO2015+ mikro remotely via USB. It plugs into the LCD control module. USB cable is not included.

Kaj je programska oprema+ USB IOBOARD za spreminjanje besedila LCD?
This is a combination of special unlocked version of software and USB IO board, which is required to control MAXPRO2015+ remotely via PC. It plugs into the LCD control module. Software lets you change welcome text (logo); you can replace that text with your company name for example. Your customized text will
shranite in uporabite pri vsakem vklopu. To je seveda neobvezna postavka.

Kateri stereo dajalnik priporočate?
Najbolje se ujemajo enote SE2000+, SE5000 DSP+ or SE8000

 

Če želite poiskati ustrezno anteno, preverite: tukaj.

Če želite poiskati primeren koaksialni kabel: tukaj.
Če želite poiskati primeren primer preverjanja: tukaj.

Dodatne informacije

Manual for MAXPRO2015+ micro FM exciter board

 

Here's a program to control this unit remotely with a PC(RS232 or USB) for SE+ V3 (MAXPRO8015 and MAXPRO2015+ micro):
http://www.pcs-electronics.com/software/2013/CyberMaxFM_v64_Setup.exe

Tukaj je gonilnik za vrata USB za XP, W2K, Vista in Windows7:
http://www.pcs-electronics.com/software/2013/CyberMaxFM_v64_Setup.exe

Tukaj je gonilnik za vrata USB za XP, Vista in Windows7, ki bi moral delovati tudi v 64:
http://www.pcs-electronics.com/software/archive_usb2comport_driver.zip

In končno gonilnik USB za Windows 10:
http://www.pcs-electronics.com/software/USB2VirtualComPort.exe

Priporočamo ta priročnik, saj razlaga veliko uporabnih stvari za katero koli FM radijsko postajo.
Section dedicated to software setup is also very helpful:
https://www.pcs.si/software/2018/Setting_up_drive_in_cinema_FM_radio_by_PCS_Electronics.pdf

 

Mnenja

Zaenkrat še ni mnenj.

Samo prijavljeni uporabniki, ki so kupili ta izdelek, lahko napišejo mnenje.