Sale!

SE5000 DSP+ stereo encoder

 3,99 124,99

In stock
Category:
 64,99

In stock

 39,99

In stock

 9,99

In stock

 4,99 7,99
 4,99 6,99
 124,99

In stock

Prices shown are without VAT (paid only in EU)

Description

Digital Stereo Encoder with DSP filters and RMS Compressor, now also with Expansion

The new SE5000 DSP+ is a high performance stereo encoder with Digital Signal Processor (DSP). It replaces our popular SE4000+ and brings new enhanced performance. Built-in compressor, precise LED limiter and balanced inputs, sharp 19KHz stereo carrier notch filter, pre-emphasis, improved channel separation and sharp filters all help to bring out really crisp sound; all coutesy of our DSP audio processor. SE5000 DSP+ can even be upgraded to RDS functionality simply by plugging-in a RDS daughter board. It is perfect for a demanding, but cost-conscious broadcaster.

SE5000 DSP+ will make sure your signal stays where you want it, providing high quality audio with excellent channel separation without causing interference to nearby channels. High quality components and printed circuit board assure 24/7 operation for years.

You can find the manual for this (and other products) here.

Why is SE5000 DSP + so great?
– Perfect for any mono FM transmitter, several output levels can be selected with jumpers
– DSP technology enables extremely sharp filters and a very deep notch at 19KHz!
– Drop-in replacement for SE3, SE4 and SE4000 DSP+!
– Works with or without LCD control module!
– Balanced or unbalanced audio inputs. This effectively eliminates annoying ground loops and hum.
– LC filtered MPX output signal.
– Built-in limiter, low pass filter and true compressor, all controlled via backlit LCD display and keys.
– You can control the sound parameters from the FM exciter’s LCD display unit!

How is SE5000 DSP+ better than SE4000 DSP+?
– Improved stereo separation
– I2C connector was redesigned for standard flat cable, now installation does not require any soldering but merely plugging a 6-pin flat cable into LCD module and stereo encoder.
– A number of small improvements that bring out better sound!
– I2C buffers permit for longer I2C cable and eliminate the notorious I2C error

Can I upgrade my CyberMaxFM transmitter (model D) with new stereo encoder?
It does make sense, especially if you have the old SE4 DSP+. Difference should be noticeable in sound quality/fidelity. We do recommend that you get the new LCD module as well (for or the MAXPRO 3+ inside CyberMax, the new LCD unit has a new I2C connector)

Technical specifications:
– Audio Response: 10Hz-15KHz, DSP filtered (Standards require upper level at 15KHz)
– DSP: 24-bit Digital Signal Processor
– 19KHz notch filter, >-70 dB typ
– Precise pre-emphasis, 50uS, 75uS or none
– Audio Input Impedance: 10Kohm, balanced or unbalanced
– Audio Input Level: 0 dB
– Distortion: <0.1%
– S/N ratio: >80 dB
– Separation: >70 dB typ. (more than any radio receiver you can buy on the market)
– Pilot Frequency: 19 KHz, DSP generated 32x oversampling
– Output Impedance: 75 Ohms
– Power Requirements: 12-15VDC / 160-200mA
– PC Board Size: 100x85mm
– Audio connectors: all RCA jacks are mounted on the board, 3-pin jumper for XLR balanced input, optional MCX or solder pads for MPX output
– Power connector: 2.1mm power socket, center (+) and screw terminals (easier for boxed units)
– Output level: Ueff 4V, 2V or 1V

 

Additional information

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.