SE3 stereo encoder
Moderators: Sir Nigel, Nina, pcs, 5r, phpBB2 - Administrators
SE3 stereo encoder
Stereo encoder for your FM TRANSMITTER
DIGITAL/ANALOG STEREO ENCODER
This unit uses DSP techniques to generate pilot and multiplexing control voltages. Pilot is generated using a 5 bit D/A converter. It has many advantages over SE-2; low pass audio filter, improved pilot generation due to DSP, stereo/mono switch, increased channel separation, simplified (no) tuning, less noise and all this in a board that is smaller and easier to assemble. Cost-efficient and simple. Includes on board control for optional maximizing of channel separation. Designed specifically as a companion for all MAX PRO series exciters, but its also compatible with any exciter that has an MPX input. All the connectors and switches are mounted on the board so connecting this unit requires no additional soldering apart for connecting the power supply line. This is a perfect KIT project even for beginners, easy to assemble and setup.
Have a quick look at the manual here:
http://www.pcs-electronics.com/software ... E3_WEB.pdf
Features:
Audio Response: 2OHz-15KHz
Audio Input Impedance: 600 Ohms, unbalanced
Audio Input Level: 0 dB
Distortion: <0.1%
S/N ratio: -60 dBm
Separation: >40 dB typ.
Pilot Frequency: 19 KHz
Output Impedance: 75 Ohms
Power Requirements: 12VDC min / 20mA
PC Board Size: 100x65mm
Audio connectors: all RCA jacks are mounted on the board
Power connector: soldering pad from + and - terminal, marked
DIGITAL/ANALOG STEREO ENCODER
This unit uses DSP techniques to generate pilot and multiplexing control voltages. Pilot is generated using a 5 bit D/A converter. It has many advantages over SE-2; low pass audio filter, improved pilot generation due to DSP, stereo/mono switch, increased channel separation, simplified (no) tuning, less noise and all this in a board that is smaller and easier to assemble. Cost-efficient and simple. Includes on board control for optional maximizing of channel separation. Designed specifically as a companion for all MAX PRO series exciters, but its also compatible with any exciter that has an MPX input. All the connectors and switches are mounted on the board so connecting this unit requires no additional soldering apart for connecting the power supply line. This is a perfect KIT project even for beginners, easy to assemble and setup.
Have a quick look at the manual here:
http://www.pcs-electronics.com/software ... E3_WEB.pdf
Features:
Audio Response: 2OHz-15KHz
Audio Input Impedance: 600 Ohms, unbalanced
Audio Input Level: 0 dB
Distortion: <0.1%
S/N ratio: -60 dBm
Separation: >40 dB typ.
Pilot Frequency: 19 KHz
Output Impedance: 75 Ohms
Power Requirements: 12VDC min / 20mA
PC Board Size: 100x65mm
Audio connectors: all RCA jacks are mounted on the board
Power connector: soldering pad from + and - terminal, marked
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
What do you think?
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
You have a PCB and parts list, its easy to work out the
schematic, if you wanted to do so.
SE3+ is actually cheap/affordable. A lot of effort went into
design, manual, testing and assembly. I think you're getting
a very fair deal here.
schematic, if you wanted to do so.
SE3+ is actually cheap/affordable. A lot of effort went into
design, manual, testing and assembly. I think you're getting
a very fair deal here.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
What you want to do is not technically possible.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
modify input impedance to 10k ?
Hi
Can the input impedance of the SE3+ be modified to make it 10k, so that it can be used with linelevel?
Thanks
Can the input impedance of the SE3+ be modified to make it 10k, so that it can be used with linelevel?
Thanks
It can be used with line level directly.
In case of any problems remove the 680ohm resistor in
the input stage and you will instantly increase input impedance.
But I think that will not be necessary.
In case of any problems remove the 680ohm resistor in
the input stage and you will instantly increase input impedance.
But I think that will not be necessary.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128