PCS Electronics PCS Electronics - home page PCS Electronics  
RegisterSearchFAQAM & FM Radio transmitters shop UsergroupsLog in
Max 4

 
Reply to topic    PCS-Electronics Forum Index » FM transmitters View previous topic
View next topic
Max 4
Author Message
stylzmovement
Compulsive poster:)
Compulsive poster:)


Joined: 11 Oct 2003
Posts: 142

us.gif

Post Max 4 Reply with quote
Ok, I got it.
Now the questions start.
I did not get a manual with this unit, but i can access it online.
I saw the diagram for connecting the DSP to the Max Pro but does the connection require polarity matching?
Do you sell the surface buttons for the MAX PRO 4 LCD?
there were no 12C cable included, what else can i use?
soldering is required for J3 on SE4 DSP.
Soldering is also required on the max pro IV to J3.
on the max pro iv what does A Mean at jumper J8
1W = 1 watt
4w = 4 watts
A = ?
there are no jumpers for the premphasis on the se4 dsp , soldering is required to obtain us 75us.

The BNC connector you have for the output can it handle 15 Watts 24 hours /7 days per week ?

Can i change this to a UHF or N Type Connector , will this void the Waranty?

other than that the piece is well made.


Last edited by stylzmovement on Fri Feb 10, 2006 6:20 am; edited 7 times in total
Fri Feb 10, 2006 2:34 am View user's profile Send private message
pcs
Site master
Site master


Joined: 18 Jan 2002
Posts: 3063
Location: Radio Land

Post Reply with quote
q: I did not get a manual with this unit, but i can access it online.
a: Check the CD

q: I saw the diagram for connecting the DSP to the Max Pro but does the connection require polarity matching?
a: Yes, exactly as on the diagram

q: Do you sell the surface buttons for the MAX PRO 4 LCD?
a: What is a surface button?

q: there were no 12C cable included, what else can i use?
a: its just normal wire

q: Soldering is also required on the max pro IV to J3.
a: We could not find a suitable pre-assembled 3-pin wire/connector,
yes you need to solder these 3 wires. I think you can manage.


q: on the max pro iv what does A Mean at jumper J8
1W = 1 watt
4w = 4 watts
A = ?
a: Automatic, in this position power is controlled by LCD module.

q: there are no jumpers for the premphasis on the se4 dsp , soldering is required to obtain us 75us.
a: We do not install those jumpers when you order stereo encoder as well. Reason is high percentage of people not disabling preemphasis and
than complaining that their stereo does not work. Its easy to install this,
should you want to operate without stereo.

q: The BNC connector you have for the output can it handle 15 Watts 24 hours /7 days per week ?
a: No, it will explode after 2 months. Of course it can handle it.

q: Can i change this to a UHF or N Type Connector , will this void the Waranty?
A: It will not fit the PCB. UHF is worse than BNC. N is better, but trust me,
this BNC can handle it.

_________________
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Fri Feb 10, 2006 11:21 am View user's profile Send private message Visit poster's website
stylzmovement
Compulsive poster:)
Compulsive poster:)


Joined: 11 Oct 2003
Posts: 142

us.gif

Post Reply with quote
pcs wrote:
q: I did not get a manual with this unit, but i can access it online.
a: Check the CD
***** nice cd i did not even know all that goodies was there *****

q: I saw the diagram for connecting the DSP to the Max Pro but does the connection require polarity matching?
a: Yes, exactly as on the diagram

q: Do you sell the surface buttons for the MAX PRO 4 LCD?
a: What is a surface button?

*** there are three push buttons next to the lcd , i will like to mount the unit in an enclosure so i will need the larger buttons to have access from the front panel *****

q: there were no 12C cable included, what else can i use?
a: its just normal wire
**** ok , good ******

q: Soldering is also required on the max pro IV to J3.
a: We could not find a suitable pre-assembled 3-pin wire/connector,
yes you need to solder these 3 wires. I think you can manage.
*** i shure can ****

q: on the max pro iv what does A Mean at jumper J8
1W = 1 watt
4w = 4 watts
A = ?
a: Automatic, in this position power is controlled by LCD module.
**** nice Feature *****

q: there are no jumpers for the premphasis on the se4 dsp , soldering is required to obtain us 75us.
a: We do not install those jumpers when you order stereo encoder as well. Reason is high percentage of people not disabling preemphasis and
than complaining that their stereo does not work. Its easy to install this,
should you want to operate without stereo.

q: The BNC connector you have for the output can it handle 15 Watts 24 hours /7 days per week ?
a: No, it will explode after 2 months. Of course it can handle it.
*** i think i will , ha ha ha ****

q: Can i change this to a UHF or N Type Connector , will this void the Waranty?
A: It will not fit the PCB. UHF is worse than BNC. N is better, but trust me,
this BNC can handle it.

** ok i hear that ****

Fri Feb 10, 2006 11:48 am View user's profile Send private message
Display posts from previous:    
Reply to topic    PCS-Electronics Forum Index » FM transmitters All times are GMT + 1 Hour
Page 1 of 1

 
Jump to: 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group