ISOTRON AM BROADCAST ANTENNA WITH AM MAX II
Moderators: Sir Nigel, Nina, pcs, 5r, phpBB2 - Administrators
-
- New registered user
- Posts: 2
- Joined: Sat Jun 26, 2004 4:52 pm
- Location: USA.
- Contact:
ISOTRON AM BROADCAST ANTENNA WITH AM MAX II
Thank you for your prompt response. Good PCS Tech-Support!
As you can see I am one of the first proud owner of the AM MAX II. I saw that you recommended the Isotron Antenna for this Transmitter. Does this antenna require any tuning or is it just connect and forget? I can invest in this Antenna providing it works.
How far apart can it be connected by Coaxial cable? In my case I want to mount this Antenna at 60' above ground.
Is there any provision or modification for Tuning an Antenna in the TX. circuitry? What is the purpose of INTEGRATION INTERVAL?
As you can see I am one of the first proud owner of the AM MAX II. I saw that you recommended the Isotron Antenna for this Transmitter. Does this antenna require any tuning or is it just connect and forget? I can invest in this Antenna providing it works.
How far apart can it be connected by Coaxial cable? In my case I want to mount this Antenna at 60' above ground.
Is there any provision or modification for Tuning an Antenna in the TX. circuitry? What is the purpose of INTEGRATION INTERVAL?
-
- New registered user
- Posts: 2
- Joined: Sat Jul 03, 2004 4:33 pm
- Location: London, UK
Robert,
The Isotrons for medium wave come pretuned to your proposed operating frequency from the factory. However, there is fine-tuning adjustment on the antenna to allow set resonance +/- 30KHz.
If you're intending to mount the antenna that 60ft above ground I don't need to tell you to use at the very least a good grade of RG213 / URM67 coaxial cable.
Phil
Transmitters 'R' Us
The Isotrons for medium wave come pretuned to your proposed operating frequency from the factory. However, there is fine-tuning adjustment on the antenna to allow set resonance +/- 30KHz.
If you're intending to mount the antenna that 60ft above ground I don't need to tell you to use at the very least a good grade of RG213 / URM67 coaxial cable.
Phil
Transmitters 'R' Us
-
- Compulsive poster:)
- Posts: 111
- Joined: Mon Mar 15, 2004 12:21 pm
- Location: Entering The Flags...but simply an arm wielding a sword signifying power
LOOP ANTENNA IDEAS
...Part 15 FCC requirements dictate the final stage of the transmitter be located as close as possible to the loop terminals.(HOW IMPRATICAL FOR THE AVERAGE LAZY JOE DOE) This constraint posses no major difficulty since the stage can be constructed on a small circuit board and mounted within the same weather-proof enclosure as the matching transformer and resonating capacitor bank. This also isolates the more expensive exciter components from the possibility of damage from a nearby lightening hit. The power can be supplied with low-cost small gauge wire since the current is under 50ma. Additionally, the power can be supplied via the coax signal line by inserting isolation transformers at both ends.
![Image](http://www.thepittsfieldinn.com/Bill/Loopadj1.JPG)
http://www.thepittsfieldinn.com/Bill/
http://www.thepittsfieldinn.com/Bill/
New price for Isotron...
![:D](./../images/smilies/icon_biggrin.gif)
French Isotron
![:)](./../images/smilies/icon_smile.gif)
A lot of constuction tips for compact Isotrons and EH antennas...
http://216.239.37.104/translate_c?hl=en ... D%26sa%3DN
Cut and Paste...
The above address has to be manually cut and pasted into your browser for proper French/English translation... ![:D](./../images/smilies/icon_biggrin.gif)
![:D](./../images/smilies/icon_biggrin.gif)
Got My Isotron Antenna...
Got my Isotron yesterday and assembled it last night. Would't you know, it rained today. Well, I braved the elements and stated tuning the unit for 1640 kHz, very touchy. Mounted the unit on a section of 10ft. mast lying against the deck at about a 45 degree angle for tune up. Must have spent a couple of hours farting around with the tuning rod. For some reason I disconnected the audio to the xmtr when I finally arrived at a SWR 1.5:1 which I thought was good enough. I reconnected the audio and my SWR went up to way over 3:1...Well into the red. I already have a good ground on the transmitter end so I don't know what's the matter.
Well, I turned up the unit and checked back later and I got an SWR 1.7:1 WITH my audio connected. An hour later the SWR is over 2:1. The SWR does seem to jump around. I'd like to get Isotron mounted vertically on a 30' telescoping mast but I'm afraid I'll lose my tuning. Does anyone have any ideas?![:-?](./../images/smilies/icon_confused.gif)
Well, I turned up the unit and checked back later and I got an SWR 1.7:1 WITH my audio connected. An hour later the SWR is over 2:1. The SWR does seem to jump around. I'd like to get Isotron mounted vertically on a 30' telescoping mast but I'm afraid I'll lose my tuning. Does anyone have any ideas?
![:-?](./../images/smilies/icon_confused.gif)
- Antler
- Compulsive poster:)
- Posts: 90
- Joined: Sat May 29, 2004 2:57 am
- Location: Somewhere between the RJAA and EHAM airports
An antenna analyser would be handy if you know someone who has one. I have the cheap MFJ and I know that Autek http://www.autekresearch.com/ makes one for under a $100.
Re the SWR, the one thing I have noticed in the past is that the enviroment can come into play and throw your antenna out of resonance. You might try hoisting it on up and see if that gives you different or better readings.
Good luck,![8)](./../images/smilies/icon_cool.gif)
Re the SWR, the one thing I have noticed in the past is that the enviroment can come into play and throw your antenna out of resonance. You might try hoisting it on up and see if that gives you different or better readings.
Good luck,
![8)](./../images/smilies/icon_cool.gif)
Thanks For The Tip...
Thanks for the tip Antler, that RF analyzer sounds like a good item to get. I read that Isotrons usually display about 30 Ohm impedance compared to a 50 ohm transmitter impedance. So I'm finally getting a steady 1.8:1 SWR with the audio turned on, not bad. The antenna shows quite a load, I'm showing about 14 watts +/- 5% meter reading which is a really good for 19 volt supply.
Well, I'll get the unit hoisted up when the weather clears. Right now, I'm getting out about 2 miles with in the tune up position and I'm sure it will vastly improve once I'm fully operational.![:)](./../images/smilies/icon_smile.gif)
Well, I'll get the unit hoisted up when the weather clears. Right now, I'm getting out about 2 miles with in the tune up position and I'm sure it will vastly improve once I'm fully operational.
![:)](./../images/smilies/icon_smile.gif)
No not lately...
I talked to a guy named Ralph today who makes the Isotron. He said to tune my transmitter up and down to find the lowest SWR. I currently have the antenna mounted horizontally on a 10' mast and the lowest point is about 5' above ground, the SWR is 1.4:1. On either side of 1640 kHz the SWR quickly goes up, so I'm confident the I've found resonance. I currently putting out a go clean signal all things considered.
Tomorrow is going to be cold, but I'm taking a trip up to Lowes and get their 30' telescoping mast fo $45. Going to see what hardware I'm going to need to do the job right. Keep you posted.![:)](./../images/smilies/icon_smile.gif)
Tomorrow is going to be cold, but I'm taking a trip up to Lowes and get their 30' telescoping mast fo $45. Going to see what hardware I'm going to need to do the job right. Keep you posted.
![:)](./../images/smilies/icon_smile.gif)
- static-radio
- New registered user
- Posts: 6
- Joined: Tue Aug 19, 2008 2:57 pm
- Location: ei.gif
- Contact:
Isotron 400
I have been looking at the Isotron 400, they are $600 dollars i the states and Canada, i see xxxxx are charging £695!!
is there any other company that does supply them?
is there any other company that does supply them?