is anyone using this unit?

Share your experience regarding radio transmitters and broadcasting with other users!

Moderators: Sir Nigel, Nina, pcs, 5r, phpBB2 - Administrators

Post Reply
User avatar
stylzmovement
Compulsive poster:)
Compulsive poster:)
Posts: 142
Joined: Sat Oct 11, 2003 8:59 pm

is anyone using this unit?

Post by stylzmovement »

is anyone outthere using the SE4 DSP?
can you share your experiance with me?

Hi , i will really like some help on the se 4 .
can this unit be used as a stand alond SG?
can the LCD be used with the unit if the unit is used as a stand alone?
where is J13 on the SE 4 ..
the unit has a very low output , how can i get this louder?
User avatar
pcs
Site master
Site master
Posts: 3132
Joined: Fri Jan 18, 2002 1:00 am
Location: Radio Land
Contact:

Post by pcs »

"Only" several hundred units out there, nothing special :)

Why would it not be usable in stand alone? Did you take 5 minutes to read the manual?

Units must be used with LCD module in stand alone mode or it won't work.

Do you call 4V pp amplitude low volume? This means the audio input of max pro 3+
must usually be closed all the way almost to zero.
How much do you need? 20-50V? 100V?
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
User avatar
stylzmovement
Compulsive poster:)
Compulsive poster:)
Posts: 142
Joined: Sat Oct 11, 2003 8:59 pm

Post by stylzmovement »

i never said that i was using the se4 dsp with a max unit.
i have max 4 here but i am using an omnia processor on it.
i am using the SE4 as a stand alone DSP to drive a Ptek exciter Mpx to Mpx
when i use the LCD on the SE4 i still get an I2C Err.
and the out put is low , what do u do to get it louder?
User avatar
pcs
Site master
Site master
Posts: 3132
Joined: Fri Jan 18, 2002 1:00 am
Location: Radio Land
Contact:

Post by pcs »

You need the SE4 DSP control module. You cannot take the lcd module from MAX PRO 4 and
stick it into SE4 DSP.

The output is not low, the card is not working at all since it misses its proper LCD module.

To operate SE4 DSP needs either:
- Its original LCD control module
- or you can connect it to MAX PRO 3 or MAX PRO 4 and control it from there, in which case LCD module is not needed.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
User avatar
stylzmovement
Compulsive poster:)
Compulsive poster:)
Posts: 142
Joined: Sat Oct 11, 2003 8:59 pm

Post by stylzmovement »

now you are making some sense, what is the cost od the control module?
give me the model number also.
User avatar
pcs
Site master
Site master
Posts: 3132
Joined: Fri Jan 18, 2002 1:00 am
Location: Radio Land
Contact:

Post by pcs »

You cannot normally buy it separately, they are being sold together for a while now.

But the cost and the unit is the same as this one:

http://www.pcs-electronics.com/test/pro ... cts_id=261

So order this one and write "program it for SE4 DSP+ please"
and we'll do that for you free of charge.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
User avatar
stylzmovement
Compulsive poster:)
Compulsive poster:)
Posts: 142
Joined: Sat Oct 11, 2003 8:59 pm

Post by stylzmovement »

i already have the unit here , so now i will need the controller device or should i send it back
User avatar
pcs
Site master
Site master
Posts: 3132
Joined: Fri Jan 18, 2002 1:00 am
Location: Radio Land
Contact:

Post by pcs »

Did you look at the link? That is "controlling device".
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Post Reply