ART1K6FH 1200W 2m 144-146MHz Pallet amplifier (48-55V) (ID: 72287)

വിവരണം

Elevate your ham radio experience with our advanced 2m all-mode wideband amplifier, featuring the latest AMPLEON transistors. This high-performance amplifier utilizes a single AMPLEON LDMOS push-pull transistor, delivering up to 1200W peak power. Designed for superior performance, it requires an excellent heatsink.

സാങ്കേതിക സവിശേഷതകളും:

• Shipping Weight: 0.9 Kg
• Frequency Range: 144-146 MHz
• Voltage: 40-55V @ 28A
• പ്രതിരോധം: Input/Output 50 ohms
• Output Power: 1000-1200W with ~10W input
• Gain: ~20 dB
• Class: B push-pull
• Temperature Compensated Bias: NXP design
• Size: 4.0 x 2.25 x 1.5 inches (LxWxH)
• Base: Standard 1/4 inch copper
• Integration: Bias disable pads for automatic VSWR protection systems

പ്രധാനപ്പെട്ടത്:
– Ensure proper shielding between the final stage and audio stage with exciter. Install a good ഫീഡ്-ത്രൂ കപ്പാസിറ്റർ  on the +48V supply wiring to prevent RF interference.
– Excessive drive levels can damage the amplifier. Ensure your equipment includes appropriate protection circuits.
– Amplifier efficiency is dependent on supply voltage. For maximum efficiency, adjust the supply according to the desired output power, typically at 1-3 dB gain compression.
– RF pallets are sensitive. If you lack sufficient experience, consider a fully finished product. Misuse can lead to damage, and no warranty is provided. Every pallet is tested and fully operational upon dispatch.
– Ensure proper airflow across the pallet to prevent overheating. Pre-order now to secure yours!
– You can find special adjustable 50-65V power supply for this amplifier ഇവിടെ! Use a good strong fan!

Manuals and drivers for most products are available under the Additional Information tab above, just under the prices. Some old manuals are ഇവിടെ. 
If your web browser blocks the download, you may have to allow it manually. You can send us questions ഇവിടെ.

Warnings and Notes:
– Do not exceed maximum supply voltage for your pallet to avoid damage.
- ഉപയോഗിക്കുക PTFE കോക്സിയൽ കേബിൾ  for RF input (RG178) and output (RG178 or RG142). Keep leads very short. This  RG142 അല്ലെങ്കിൽ .141 semirigid-നുള്ള N പെൺ ഫ്ലേഞ്ച് - എളുപ്പത്തിൽ ഇൻസ്റ്റാൾ ചെയ്യുക തികഞ്ഞതാണ്!
– A heatsink is essential. Ensure proper airflow across the pallet to prevent overheating.

ശുപാർശ ചെയ്യുന്ന ആക്സസറികൾ:
ഞങ്ങൾ ശുപാർശ ചെയ്യുന്നു antenna analyzer for checking SWR of the antennas. Grounding kits for lightning protection can be purchased ഇവിടെ. They should be installed at the antenna (if needed, most dipoles are grounded anyway), at the tower base and at the point of entrance into transmitter building. Also use സ്വയം-സീലിംഗ് ടേപ്പ് which turns into rubber and protects moisture from entering your antenna system. You might also need Antenna tower to place the antennas. കോക്‌സിയൽ കേബിളും കണക്ടറുകളും are available as well.