Sale!

TVMAX8000V+ 10W and 20W VHF LO+HI TV TRANSMITTER

£3,04£209,07

In stock
£174,23

In stock

£191,65

In stock

£87,11

In stock

£19,16

In stock

£52,26

In stock

£34,84

In stock

£56,62

In stock

£39,19

In stock

£60,97

In stock

£26,13

In stock

£209,07

In stock

£5,22£197,76

In stock

£95,82

In stock

£3,48£6,96
£78,40

In stock

Prices shown are without VAT (paid only in EU)

Description

10W/ 20W, all analog TV standards supported, VHF band I and III

We decided to bring out a new model of TV exciter based on technology similar to our FM exciter boards! Our new 10W/20W  VHF and 7W UHF TV transmitter is your ticket into the world of TV. With support for remote directional coupler and RF power limit so you can build 100W, 200W, 500W or stronger TV transmitter. Build your own TV studio and broadcast your own TV program! Transmit movies from your PC to your living room, re-transmit the TV program you’ve never been able to receive in your valley, run a college TV station, cover rural areas of Africa with TV signal from satellite stations, run a hotel cable system info pages or just have fun… this unit will keep you busy during the cold winter evenings and is sure to provide lots of fun for many months to come! Unit is available as a populated and tested board or a rack-mounted ready-to-use transmitter. Rack mounted unit runs from 20-48V DC from mains power adapter. Optional stereo encoder board plugs into the main transmitter board to provide stereo sound and DSP processing for NTSC. Up to 10W of output power offers from several hundred meters up to about 10km of range depending on antenna type used on transmitting and receiving side. High-gain yagis on both sides might offer even more range in favorable conditions.

Unit is rugged and comes with SWR protection, made for 24/7/365 operation. Each unit has a wide-angle high contrast back-lit LCD display. Output power and channel can now be adjusted via LCD module.

Look HERE for all manuals, drivers and support.

How is the TVMAX8000+ different from the old and now obsolete TVMAX6010V?
– Support for MAXLINK II for much improved audio performance (in 1H rack you now get XLR and RCA stereo inputs)
– Header for bargraph for VU meter (External SWR and Power signal when used to drive pallets)
– Stand-by header wired to new LCD type

General features:
– Powered from 20-48V (requires 48V for 10W and 53V for 20W)
– DSB AM modulation, universal all audio and TV standards
– Fits our new 19″ 1H rack
– Built-in CPU for controlling and monitoring
– PC remote control via RS232, USB or Ethernet (requires IO board or ethernet expansion board)
– It can now read POWER and SWR from external directional coupler (DIGIAMP), it can also monitor amplifier temperature, voltage, current
– Adjustable TV channel (via LCD module with up/down keys)
– Easily adjustable TV and sound standard (via LCD module)
– Built-in test signal generator
– Supports all world TV standards: All PAL versions, SECAM, NTSC
– TV Channels: All VHF HIGH (175-225MHz in 125KHz steps)
– TV Channels: All VHF LOW (55-88MHz in 125KHz steps)
– SWR and TEMP protection
– Stereo sound possible with plug-in board (NTSC)
– Friendly user interface
– Output power: 10W/20W typ, adjustable from 0 to Pmax via LCD display,
– Output impedance 50 Unbalanced, VSWR less than 2:1 for full output
– Output connector BNC female ( rear panel )
– Frequency range: TV VHF band
– Audio connectors: RCA (cinch)
– Audio level: 1Vpp
– Video level: 1Vpp
– Audio input impedance: 10K resistive, unbalanced
– Pre-emphasis 50 or 75usec
– Regulated power supply: DC 20-48V/2A (more power at higher voltage)
– Weight: 0.8kg
– Dimensions: 100x125mm, same as TVMAX 5000+
– A fan is needed at all times (blowing across the board)

What is the DSP Stereo Encoder for USA/NTSC?
– This add-on card enables stereo sound, it was designed for NTSC system, used in USA and most of South/North America.

What is the external power/swr meter with DIGIAMP?
– This add-on card enables building strong TV transmitters, it is placed after an amplifier and makes it possible to show output power and swr on the LCD display of the transmitter. The add-on card connects to the TVMAX6000 via simple 14-pin DIGIAMP flat cable. Coming soon.

What is the USB IO board for?
– This add-on card lets you connect this transmitter to the PC via standard USB cable (not included). You can fully monitor transmitter via PC (power, frequency and other settings). 6-pin flat cable also connects BNC for Video and Audio inputs to TVMAX6000.

What is the Ethernet remote control module for?
– This add-on card lets you connect this transmitter to the PC via Ethernet network. You can control and monitor the status of your transmitter over Ethernet or Internet. Requires also USB IO board as it plugs into it.

What is the Predrilled LCD front panel?
– This is a square piece of aluminum with predrilled holes for LCD display, buttons and LED diodes. It also has 4 holes in the corner so you can easily mount this to your case. This makes it much easier to mount the transmitter into a nice looking case (eliminates the hard work with the LCD).

Antenna options
You can check all our TV antennas here.

This is a perfect little TV antenna for this transmitter. Some antennas are listed below.

To purchase coaxial cable and connectors for this transmitter look
HERE.

 

Additional information

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.