SE3000AN+ stereo encoder

New hybrid digital/analog encoder with incredible sound

You can find the manual for this (and other products) here.

Some people do not like the sound of DSP so we did our best to duplicate its performance with analog building blocks. We added the popular compressor from our old LIMBO I limiter unit and balanced inputs. The new SE3000 AN+ was born; a high performance stereo encoder without DSP, but with extremely elaborate analog filter circuitry that rivals the sharpness of its DSP cousin. We have to admit, this unit does sound extremely well and is sure to please many golden ears out there. To recapitulate, we have a built-in ALC/compressor, precise LED limiter and balanced inputs, sharp 19KHz stereo carrier notch filter (>60dB), pre-emphasis, excellent channel separation and sharp low pass filters all help to bring out really crisp sound. SE3000 AN+ can even be upgraded to RDS functionality simply by plugging-in a RDS daughter board. It is perfect for a demanding, but cost-conscious broadcaster. SE3000 AN+also comes with a new MaxLink connector, designed to connect stereo encoder to our fm exciters. This connection lets you select stereo/mono via the FM exciter's LCD module and also provides supply voltage for its operation.
SE3000 AN+ will make sure your signal stays where you want it, providing high quality audio with excellent channel separation without causing interference to nearby channels. High quality components and printed circuit board assure 24/7 operation for years.

Why is SE3000 AN + so great?
- Perfect for any mono FM transmitter, several output levels can be selected with jumpers
- Works without LCD control module
- Can be connected to our FM exciter and controlled via the same LCD module (mono/stereo mode selection).
- DSP-like filters, extremely sharp and a very deep notch at 19KHz!
- Drop-in replacement for SE4000/5000 DSP+!
- Balanced or unbalanced audio inputs. This effectively eliminates annoying ground loops and hum.
- LC filtered MPX output signal.
- Built-in limiter, low pass filter and true compressor/ALC
- 3-pin header for VU meter added (check VUMAX-1)

Technical specifications: - Audio Response: 10Hz-15KHz, DSP filtered (Standards require upper level at 15KHz)
- 19KHz notch filter, >60 dB typ
- Precise pre-emphasis, 50uS, 75uS or none
- Audio Input Impedance: 10Kohm, balanced or unbalanced
- Audio Input Level: 0 dB
- Distortion: <0.1%
- S/N ratio: >80 dB
- Separation: >70 dB typ. (more than any radio receiver you can buy on the market)
- Pilot Frequency: 19 KHz, DSP generated 32x oversampling
- Output Impedance: 75 Ohms
- Power Requirements: 12-15VDC / 100-150mA
- PC Board Size: 100x85mm
- Audio connectors: all RCA jacks are mounted on the board, 3-pin jumper for XLR balanced input, optional MCX or solder pads for MPX output
- Power connector: 2.1mm power socket, center (+) and screw terminals (easier for boxed units)
- Output level: Ueff 4V, 2V or 1V
- Weight: 0.1Kg

Ovaj proizvod je upisan u nau trgovinu dana Tuesday 15 April, 2008.

*Izaberite količinu za svaki eljeni proizvod i kliknite 'Koarica' dole.

Prikazujem 1 do 4 (od 4 proizvoda)

Rezultati: 1

Ime	Model	Količina	Cijena
SE3000AN+ stereo encoder			96,14GBP
RDS daughter board (RDSMAX 4000+ mini)			87,40GBP
10cm Maxlink/I2C cable to MAX PRO 3+			3,49GBP
30cm Maxlink/I2C cable to MAX PRO 3+			3,49GBP

Prikazujem 1 do 4 (od 4 proizvoda)

Rezultati: 1