Sale!

Pokeys devices (PoUSB12 USB/RS232 and PoKeys56E Ethernet I/O Device)

 4,99 39,99

In stock
Category:
 4,99

In stock

 39,99

In stock

Prices shown are without VAT (paid only in EU)

Description

The PoUSB 12 is a USB 2.0 (12Mbs maximum speed) to RS-232 bridge converter which is simple, cost effective, very small and easy to use. It uses a USB-B type connector to connect to your PC and is based on the CP2102 Bridge from Silicon Labs. The PoUSB 12 provides the user with multi baud rate serial data and access to USB control signals in a convenient 8 pin 2,54 mm (0.1″) pitch package.

Main Features:
– USB 2.0 compliant (12Mbps maximum speed).
– Suspend supported.
– Xon/Xoff handshaking supported (300bps to 1Mbps).
– UART supports 5-8 bit data, 1-2 Stop bits, odd/even and no parity.
– Integrated EEPROM for Vendor ID, product ID, serial and release number.
– On-chip 3.3V regulator available with power on reset circuit.
– Self powered or USB powered.
– TX and RX signal levels are between 0V and 3.3V (5V tolerant).
– Temperature range: -40 to +85 °C.
– Small size: 17mm x 12mm x 15mm.
– Virtual COM port drivers for Windows, Linux and MACOS.
– Can be used as ICP programmer for LPC2000 microcontrolers

Windows driver!
Linux driver!
Mac driver!
PoUSB12 manual!

 

 

 

PoKeys56E is an easy-to-use Ethernet device that combines a lot of inputs and outputs, and does not require complex programming knowledge. Pokeys56 provides 55 digital I/O (5V tolerant), 7 analog inputs (12-bit). All the I/O are controlled by the provided software which allows either to use the graphical user interface or advanced console type interface. The settings can be stored on the device, so no special software is needed on target system. PoKeys56 can be used as industrial or CNC control or data acquisition board.

Requirements

  • Ethernet connection between host computer and PoKeys56E device
  • 5V DC power supply with 400 mA. If any additional peripheral is connected to PoKeys56E, use appropriately more powerful power supply.
  • Included software requires Windows 2000/XP/Vista/Windows 7 with .NET framework 3.5 installed (ONLY FOR SYSTEMS WHERE THE DEVICES WILL BE CONFIGURED, TARGET SYSTEM NEEDS NO SOFTWARE INSTALLATION FOR THE DEVICE TO OPERATE AS A STANDARD NEWTORK DEVICE).

Features

  • Ethernet 10/100 with DHCP client or fixed IP support
  • TCP connection with device
  • 55 digital inputs with pull-up resistors
  • 55 software controlled digital outputs
  • 7 analog inputs (12-bit) with adjustable low-pass filtering support
  • Up to 26 encoder pair inputs (3 high-speed encoder inputs, 1 ultra high speed encoder input)
  • Digital counters on specific digital input pins
  • Up to 16×8 matrix keyboard
  • Two 8×8 matrix LED display support
  • Up to 6 high-speed fully configurable PWM outputs support (25 MHz PWM timer)
  • HD44780-based character LCD support (up to 4×20 characters)
  • PoExtBus support for adding up to 10 external shift registers = 80 additional outputs
  • PoNET devices support (48-key CNC keyboard, etc…)
  • Modbus TCP support (access to digital IO, analog inputs, encoders’ counters, digital counters values, PWM outputs, LCD display, LED matrix display, PoExtBus devices, matrix keyboard status)
  • Support for up to 10 sensors on I2C bus, up to 10 sensors on 1-wire bus and up to 7 analog sensors
  • Web interface with newly designed dashboard and I/O status display with multiple user accounts
  • Support for communication with devices on I2C and 1-wire buses
  • Support for Connection signal output
  • Communication compatible with PoKeys55 on application layer (data packet structure)
  • Intuitive and user-friendly software
  • Third-party support via communication DLL library and extensive protocol specification document that allows porting to other systems
  • Plug-in for Artsofts Mach 3 CNC software under development

Additional information

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.