Dispositivos Pokeys (PoUSB12 USB/RS232 y PoKeys56E Ethernet I/O Device)

Descripción

El PoUSB 12 es un convertidor de puente USB 2.0 (12Mbs de velocidad máxima) a RS-232 que es simple, rentable, muy pequeño y fácil de usar. Utiliza un conector tipo USB-B para conectarse a su PC y se basa en el puente CP2102 de Silicon Labs. El PoUSB 12 proporciona al usuario datos en serie de múltiples velocidades en baudios y acceso a señales de control USB en un conveniente paquete de paso de 8 pines y 2,54 mm (0,1 ″).

Principales características:
- Compatible con USB 2.0 (velocidad máxima de 12 Mbps).
- Suspender apoyado.
- Compatible con protocolo de enlace Xon / Xoff (300bps a 1Mbps).
- UART admite datos de 5-8 bits, 1-2 bits de parada, pares / impares y sin paridad.
- EEPROM integrada para ID de proveedor, ID de producto, número de serie y de versión.
- Regulador en chip de 3.3V disponible con circuito de reinicio.
- Autoalimentado o alimentado por USB.
- Los niveles de señal TX y RX están entre 0V y 3.3V (tolerante a 5V).
- Rango de temperatura: -40 a +85 ° C.
- Tamaño pequeño: 17 mm x 12 mm x 15 mm.
- Controladores de puerto COM virtual para Windows, Linux y MACOS.
- Se puede utilizar como programador ICP para microcontroladores LPC2000

Controlador de Windows!
Controlador de Linux!
Controlador de Mac!
Manual de PoUSB12!

PoKeys56E is an easy-to-use Ethernet device that combines a lot of inputs and outputs, and does not require complex programming knowledge. Pokeys56 provides 55 digital I/O (5V tolerant), 7 analog inputs (12-bit). All the I/O are controlled by the provided software which allows either to use the graphical user interface or advanced console type interface. The settings can be stored on the device, so no special software is needed on target system. PoKeys56 can be used as industrial or CNC control or data acquisition board.

Requirements

• Ethernet connection between host computer and PoKeys56E device
• 5V DC power supply with 400 mA. If any additional peripheral is connected to PoKeys56E, use appropriately more powerful power supply.
• Included software requires Windows 2000/XP/Vista/Windows 7 with .NET framework 3.5 installed (ONLY FOR SYSTEMS WHERE THE DEVICES WILL BE CONFIGURED, TARGET SYSTEM NEEDS NO SOFTWARE INSTALLATION FOR THE DEVICE TO OPERATE AS A STANDARD NEWTORK DEVICE).

Características

• Ethernet 10/100 with DHCP client or fixed IP support
• TCP connection with device
• 55 digital inputs with pull-up resistors
• 55 software controlled digital outputs
• 7 analog inputs (12-bit) with adjustable low-pass filtering support
• Up to 26 encoder pair inputs (3 high-speed encoder inputs, 1 ultra high speed encoder input)
• Digital counters on specific digital input pins
• Up to 16×8 matrix keyboard
• Two 8×8 matrix LED display support
• Up to 6 high-speed fully configurable PWM outputs support (25 MHz PWM timer)
• HD44780-based character LCD support (up to 4×20 characters)
• PoExtBus support for adding up to 10 external shift registers = 80 additional outputs
• PoNET devices support (48-key CNC keyboard, etc…)
• Modbus TCP support (access to digital IO, analog inputs, encoders’ counters, digital counters values, PWM outputs, LCD display, LED matrix display, PoExtBus devices, matrix keyboard status)
• Support for up to 10 sensors on I²C bus, up to 10 sensors on 1-wire bus and up to 7 analog sensors
• Web interface with newly designed dashboard and I/O status display with multiple user accounts
• Support for communication with devices on I²C and 1-wire buses
• Support for Connection signal output
• Communication compatible with PoKeys55 on application layer (data packet structure)
• Intuitive and user-friendly software
• Third-party support via communication DLL library and extensive protocol specification document that allows porting to other systems
• Plug-in for Artsofts Mach 3 CNC software under development