I recently purchase the above, but when i try to use it with the lcd i get 12c ERR and can't do anything with the lcd unit.
Thanks in advance
SE4000 DSP+ Problem
Moderators: Sir Nigel, Nina, pcs, 5r, phpBB2 - Administrators
How did you set the AUTO/LCD jumper?
Marko
Marko
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
If memory serves me right this jumper should be removed.
I'm not sure whether your LCD is for combination of MAX PRO 3+ and SE4000 or just for SE4000,
can't remember what exactly was in your order. How are you running SE4000, alone or with Maxpro3?
Marko
I'm not sure whether your LCD is for combination of MAX PRO 3+ and SE4000 or just for SE4000,
can't remember what exactly was in your order. How are you running SE4000, alone or with Maxpro3?
Marko
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
I am runnning it in standalone mode, The lcd was purchased with a max pro 3+. I am asuming that the lcd will work with both. It works without the lcd fine, i just cant change any settings etc, I have also followed the instructions in setting it up in auto, but the red light is on all the time, so i can't set a level
Ok, here is how this works.brig wrote:I am runnning it in standalone mode, The lcd was purchased with a max pro 3+. I am asuming that the lcd will work with both. It works without the lcd fine, i just cant change any settings etc, I have also followed the instructions in setting it up in auto, but the red light is on all the time, so i can't set a level
LCD for MAXPRO3+ can work in 2 modes:
1. Just for MAX PRO 3+ (LCD attached directly to max pro 3+, no se4000)
2. For MAX PRO 3+ and SE4000 - (LCD attached directly to max pro 3+, SE4000 attached to it via I2C cable)
As you see you can't just stick MAX PRO 3+ LCD module into SE4000, it won't work.
What to do now:
- You can use it as stated under point 2 above
- You can nicely ask me to send you the microcontroller for dedicated SE4000 LCD module, and if I say yes you can replace
just the microcontroller when it arrives and you're ready to roll.
Marko
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Thanks Marco that would be great.pcs wrote:Ok, here is how this works.brig wrote:I am runnning it in standalone mode, The lcd was purchased with a max pro 3+. I am asuming that the lcd will work with both. It works without the lcd fine, i just cant change any settings etc, I have also followed the instructions in setting it up in auto, but the red light is on all the time, so i can't set a level
LCD for MAXPRO3+ can work in 2 modes:
1. Just for MAX PRO 3+ (LCD attached directly to max pro 3+, no se4000)
2. For MAX PRO 3+ and SE4000 - (LCD attached directly to max pro 3+, SE4000 attached to it via I2C cable)
As you see you can't just stick MAX PRO 3+ LCD module into SE4000, it won't work.
What to do now:
- You can use it as stated under point 2 above
- You can nicely ask me to send you the microcontroller for dedicated SE4000 LCD module, and if I say yes you can replace
just the microcontroller when it arrives and you're ready to roll.
Marko
Contact me via email.
Best regards,
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128
Marko - PCS Electronics
--------------------------------------------------------
Turn your PC into a FM radio station!
http://www.pcs-electronics.com
fax +386 4 2316 128