PCS Electronics, radio and TV transmitter superstore! Chat with our engineers or leave a message English Espanol Portugues Norwegian    
  Topo » Catálogo » Social Login Minha Conta  |  Conteudo do cesto  |  Verificação Final   
Categorias
Special sale items
FM transmitters->
RF accesories for transmitters->
FM amplifiers->
FM radio antennas
TV Transmitters->
PC Transmitters
TV amplifiers->
TV antennas
Coaxial cable and connectors
RDS Encoders
Stereo encoders
Wireless audio/video links
Instruments
Electronic components->
Software
Cool Stuff->
Solar power
Studio equipment->
DEVA Broadcasting->
AM transmitters - Coming back
RF service and design
O que há de novo?
DB90-RX – IP Audio Decoder
DB90-RX – IP Audio Decoder
120.00EUR
Nossos Manuais de rádio
Como Começar
Questões Frequentes
Making Your Own Transmitter
Cabo Coaxial
Equipamento de Audio
Esquemas
Novos esquemas
Wizards
Amplificadores
Antenas
Power Supply
Recomendado Lêr
Soldar
Comentarios
Informação
Sobre PCS Electronics
Entrega e devolução
Requisitar
Sopporte
Actual Stock
Questões frequentes
Forum
Contacte-nos
Distribuidores
Nota de Privacidade
Affiliate Program
Affiliate Information
Affiliate Program FAQ
Affiliate Log In
Vouchers
Cheques prenda FAQ
Seguran‡a


PayPal and credit cards accepted!
Power Supply Power Supply
Idiot's guide to Power supplies
If you're planing to power your transmitter from batteries, than skip this section! You might want to read it to get an idea of what others do.
Most home-built and small power hobby transmitters need a good 12-15 volt, 2 (Minimum) - 8 (Future expansion) Ampere Stabilized power supply. Note stabilized was printed in bold type, meaning output voltage is regulated and stabilized to spefic value.
Wall-wart types are usually not of this type. They can output even 20V when in load-free mode and only go down to rated 12V under substantial load. This is not what you want to use as it may damage your transmitter and will definitely present as a strong 100Hz hum on your signal from the lack of proper stabilisation. Short circuit protection is useful, but not mandatory. A fuse serves well instead of protection and you should definitely use one. They cost 5 cents and a final RF transistor can cost you more than 100 US$/Euro. Do your math.
Adjustable output voltage gives you an additional feature, you will be able to change your transmitter's output power by changing voltage of your power supply. Not bad. You can sometimes squeeze more power out of your transmitter if you raise voltage over rated voltage for your transmitter just a little bit. But be careful, this is likely to destroy your output transistor, sometimes blow some electrolytic capacitors or cause excessive heating.

Importance of proper power supply is often underestimated. Poor power supply can cause several serious problems; add hum to your signal, cause interference to your neighbors (typical for AM systems where RF leaks into power lines), low current rating, unstable operation under RF field etc. Complicated laboratory power supply units with lots of un-shielded electronics are often susceptible to RF fields meanning they can uncontrollably raise their output voltage or short-circuit protection can trip when the current is not even reaching 10% of the limit. A good power supply for transmitters should be RF shielded.

Radio Shack is a good place to look for cheap stuff, as well as ham stores and ham fests.If you prefer to build your equipment by yourself, get your soldering irons and check out these projects below:


Adjustable 1A power supply
This is a simple variable output power supply. Now, left of this circuit would be standard line voltage transformer (110-220/18V) and a standard gretz rectifier with smoothing caps (10000uF or even better more). The heatsink of the 317 regulator must be isolated from the ground (aluminum heatsink).

usm4.gif (20737 bytes)



3A 13.8V fixed-voltage power supply
;

usm3.jpg (35749 bytes)


This is a pretty strait-forward circuit. You might need to bypass C5 with a bigger capacitor (10-100uF). Diode D makes up for the BE loss of 0.7V of the 2N3055 transistor. If you need higher voltage, use 7815 instead of 7812 and connect pin 3 directly to ground. This will give you 14-14.3V on the output. I built several power supplies like that for my CB/ham stations and they work very well. Of course you have to add mains transformer and rectifier bridge + smoothing caps, just like above. Caps should be as big as possible (20000uF or more).



28V high-current power supply for 40-200W RF power amplifiers;

usm3.jpg (35749 bytes)


This design is from the ARRL handbook 2005, we recommend this book to anyone as it covers all aspects in RF design including antennas, transmitters, basic electronics, filters, amplifiers and others. This power supply is very convenient for 40-200W RF amplifiers which often operate from 24V. Check ARRL handbook for PCB layout and additional details. We even have a link to this book in our Recommended reading section.




Discuta este artigo no nosso forúmForum!
Continuar
Carrinho de Compras
0 items
Os Mais vendidos
Os Mais vendidos
50W Nano FM transmitter package B (Exterminator)
48V/1800W mains power supply
Vertical 2-bay System ECOMAX7 (2-step combiner) wideband
STMAX3015 stereo FM exciter
500W SE+ FM transmitter package with antenna
600W circular dipole
BLF188XR
1KW Exterminator antenna
RigExpert antenna analyzers
1000W BLF188XR FM band 48V pallet
SE5000 DSP+ stereo encoder
D&R AirLite USB 8 channel mixer
Especiais
Wide band 2500W circular dipole - Stainless steel
Wide band 2500W circular dipole - Stainless steel
269.99EUR
267.99EUR
Pesquisa Rápida
 

Use palavras chave para encontrar o produto que procura.
Notificações

Sign up and receive special deals, discount codes, news and product updates delivered to your inbox. Emails are sent out ~ 1x/month.

Anúncios
Visita o nosso forum
ultimos comentarios:

clica para entrar no forum
Google™ translate
English French Spanish
German Italian Portuguese
Korean Japanese Arabic Greek Turkce
Moeda
   

Outras moedas

Contacte-nos | Sobre PCS Electronics | Sopporte | Questões frequentes | Como Começar | Entrega e devolução
Todos precios en US$ | Todos precios en EURO | Manuais, software e suporte

Todo o texto deste site, productos descrições, manuais e certeficados
Copyright © by PCS Elektronik d.o.o.
Powered by osCommerce